2 Pack of Englander Auger Motors: PU-047040-AMP-N

Description: 2 Pack of Englander Auger Motors: PU-047040-AMP-N1RPM CCW RotationHuge Savings Over OEM Part!Buy 2 Of These For Less Than 1 Of The OEMWhisper Quiet Englander Auger Motor Replacements / Upper & Lower Motors Part Number: AMP20131-1 More Info: This auger motor is designed to fit Englander pellet stoves including models 25-PDV and 25-PDVC (two per unit), and is the stirrer motor on Englander's 10-CPM multi-fuel stove.Our Englander auger motor comes fully assembled, is simple to install and has built-in leads that connect to your existing stove's wiring. The auger motor mounts securely to the auger shaft and will have your stove up and running in minutes.This auger motor is as powerful as it is quiet and provides a steady rotation that allows for an even distribution of fuel.Our Englander replacement auger motor will have your auger system running smoothly while keeping you warm during the cold winter months. Instructions for replacing the Auger Motors To replace the Top Auger, all the fuel must be removed from the hopper as well as from the Top Auger assembly. Once this is done, the four bolts that hold in the bearing can be removed, followed by the complete auger assembly. Loosen the two (2) set screws with a 1/8” Allen wrench, which will disconnect the bearing from the shaft (the bearing assembly and auger assembly can be replaced by reversing this procedure). When placing the auger assemblies in the unit, always tighten the four bolts in a diagonal pattern to ensure the bearings and shafts are aligned properly. NOTE: Follow the same procedure to work on the bottom auger, with the exception that the pellets do not have to be removed from the hopper. Replace Part # PU-047040Compatibility This product is compatible with the following modelsEnglander25-PDV Products from us compatible with the Englander 25-PDV 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack) Englander Auger Motor 1 RPM Counter Clockwise (OEM): PU-047040 Englander Auger Motor 1RPM By Gleason Avery: PU-047040-GA Englander Auger Bearing (OEM), PU-UCF204-12 Englander Auger Bearing: PU-UCF204-12-AMP Englander 6" Round Combustion Motor to Housing Gasket: PU-CMG Englander Auger Bearing Gasket (For Models Pre 2001): PU-ABG 12" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wire Extension Connector. Extends current terminal 12 extra inches. 6" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wiring adapter for switching a male spade connector into a female spade connector. 6" Wiring adapter for switching a male spade connector into a female spade connector. Combustion Blower 1/4" Slotted-Hex Piercing Screws (Set of 6): HDW500 Combustion Blower Quick Disconnect Mounting Screw Hex Nuts (Set of 6): HDW600 3" Wiring adapter for switching a female spade connector into a male spade connector.25-PDVC Products from us compatible with the Englander 25-PDVC 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack) Englander Auger Motor 1 RPM Counter Clockwise (OEM): PU-047040 Englander Auger Motor 1RPM By Gleason Avery: PU-047040-GA Englander Auger Bearing (OEM), PU-UCF204-12 Englander Auger Bearing: PU-UCF204-12-AMP Englander 6" Round Combustion Motor to Housing Gasket: PU-CMG Englander Auger Bearing Gasket (For Models Pre 2001): PU-ABG 12" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wire Extension Connector. Extends current terminal 12 extra inches. 6" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wiring adapter for switching a male spade connector into a female spade connector. 6" Wiring adapter for switching a male spade connector into a female spade connector. Combustion Blower 1/4" Slotted-Hex Piercing Screws (Set of 6): HDW500 Combustion Blower Quick Disconnect Mounting Screw Hex Nuts (Set of 6): HDW600 3" Wiring adapter for switching a female spade connector into a male spade connector.25-PI Products from us compatible with the Englander 25-PI 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack) Englander Auger Motor 1 RPM Counter Clockwise (OEM): PU-047040 Englander Auger Motor 1RPM By Gleason Avery: PU-047040-GA Englander 2 RPM Auger Feed Motor: CU-047042 Englander 2RPM Auger Motor (USA Made By Gleason Avery): CU-047042-AMP Englander Auger Bearing (OEM), PU-UCF204-12 Englander Auger Bearing: PU-UCF204-12-AMP Englander 6" Round Combustion Motor to Housing Gasket: PU-CMG Englander Auger Bearing Gasket (For Models Pre 2001): PU-ABG 12" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wire Extension Connector. Extends current terminal 12 extra inches. 6" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wiring adapter for switching a male spade connector into a female spade connector. 6" Wiring adapter for switching a male spade connector into a female spade connector. 3" Wiring adapter for switching a female spade connector into a male spade connector.25-PAF Products from us compatible with the Englander 25-PAF 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack) Englander Auger Motor 1 RPM Counter Clockwise (OEM): PU-047040 Englander Auger Motor 1RPM By Gleason Avery: PU-047040-GA Englander 2 RPM Auger Feed Motor: CU-047042 Englander 2RPM Auger Motor (USA Made By Gleason Avery): CU-047042-AMP Englander Auger Bearing (OEM), PU-UCF204-12 Englander Auger Bearing: PU-UCF204-12-AMP Englander 6" Round Combustion Motor to Housing Gasket: PU-CMG Englander Auger Bearing Gasket (For Models Pre 2001): PU-ABG 12" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wire Extension Connector. Extends current terminal 12 extra inches. 6" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wiring adapter for switching a male spade connector into a female spade connector. 6" Wiring adapter for switching a male spade connector into a female spade connector. 3" Wiring adapter for switching a female spade connector into a male spade connector.25-PFS Products from us compatible with the Englander 25-PFS 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack) Englander Auger Motor 1 RPM Counter Clockwise (OEM): PU-047040 Englander Auger Motor 1RPM By Gleason Avery: PU-047040-GA Englander Auger Motor Replacement: PU-047040-AMP-N Englander Auger Bearing (OEM), PU-UCF204-12 Englander Auger Bearing: PU-UCF204-12-AMP Englander Auger Motor Support Sleeve: PU-AMS-AMP Englander 6" Round Combustion Motor to Housing Gasket: PU-CMG Englander Auger Bearing Gasket (For Models Pre 2001): PU-ABG 12" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wire Extension Connector. Extends current terminal 12 extra inches. 6" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wiring adapter for switching a male spade connector into a female spade connector. 6" Wiring adapter for switching a male spade connector into a female spade connector. 3" Wiring adapter for switching a female spade connector into a male spade connector.25-CAB80 Products from us compatible with the Englander 25-CAB80 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack) Englander Auger Motor 1 RPM Counter Clockwise (OEM): PU-047040 Englander Auger Motor 1RPM By Gleason Avery: PU-047040-GA Englander Auger Motor Replacement: PU-047040-AMP-N Englander Bottom Auger Shaft: PU-AF11B-AMP Englander Auger Bearing (OEM), PU-UCF204-12 Englander Auger Bearing: PU-UCF204-12-AMP Englander Auger Motor Support Sleeve: PU-AMS-AMP Englander Auger Shaft Locking Collar: PU-2X570 12" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wire Extension Connector. Extends current terminal 12 extra inches. 6" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wiring adapter for switching a male spade connector into a female spade connector. 6" Wiring adapter for switching a male spade connector into a female spade connector. 3" Wiring adapter for switching a female spade connector into a male spade connector.25-PDVP Products from us compatible with the Englander 25-PDVP 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack) Englander Auger Motor 1 RPM Counter Clockwise (OEM): PU-047040 Englander Auger Motor 1RPM By Gleason Avery: PU-047040-GA Englander Auger Motor Replacement: PU-047040-AMP-N Englander Auger Bearing (OEM), PU-UCF204-12 Englander Auger Bearing: PU-UCF204-12-AMP Englander Auger Motor Support Sleeve: PU-AMS-AMP Englander Auger Bearing Gasket (For Models Pre 2001): PU-ABG Englander Auger Shaft Locking Collar: PU-2X570 12" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wire Extension Connector. Extends current terminal 12 extra inches. 6" Wiring adapter for switching a female spade connector into a male spade connector. 12" Wiring adapter for switching a male spade connector into a female spade connector. 6" Wiring adapter for switching a male spade connector into a female spade connector. 3" Wiring adapter for switching a female spade connector into a male spade connector.25-PDVE, 55-SHP22E Products from us compatible with the Englander 25-PDVE, 55-SHP22E Englander Combustion Blower With Housing (OEM): PU-076002B 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack) Englander Combustion Blower With Housing (Made By Fasco): PU-076002B-AMP Englander Auger Motor 1 RPM Counter Clockwise (OEM): PU-047040 Englander Auger Motor 1RPM By Gleason Avery: PU-047040-GA Englander Auger Motor Replacement: PU-047040-AMP-N Englander Bottom Auger Kit Includes Shaft, Bearing, Locking Collar & Gaskets - NO MOTOR: PU-AF11B-SET-AMP Englander Bottom Auger Shaft: PU-AF11B-AMP Englander Auger Bearing (OEM), PU-UCF204-12 Englander Combustion Blower Exhaust Motor Mount (For PU-076002B) Englander Auger Bearing: PU-UCF204-12-AMP Englander Combustion Blower Impeller (For PU-076002B) Englander Auger Motor Support Sleeve: PU-AMS-AMP Englander Burn Pot Gasket: PU-BPG Englander Auger Shaft Locking Collar: PU-2X57010-CPM Products from us compatible with the Englander 10-CPM 2 Pack Of Englander Auger Motors By Gleason Avery: PU-047040-AMP-GA (2 Pack) Englander Auger Motor 1 RPM Counter Clockwise (OEM): PU-047040 Englander Auger Motor 1RPM By Gleason Avery: PU-047040-GA Englander 2 RPM Auger Feed Motor: CU-047042 Englander 2RPM Auger Motor (USA Made By Gleason Avery): CU-047042-AMP Englander Auger Motor 2RPM: CU-047042-AMP Englander Ceramic Firebrick Fiber Board: CPM-CFB Englander Auger Motor Replacement: PU-047040-AMP-N Englander Cartridge Heater Igniter: PU-CH6-AMP Englander Combustion Blower Gasket Set: PU-CBMG Englander Auger Coupler: CA-AC Englander Burn Pot Gasket: PU-BPG Englander Combustion Housing Gasket Englander Auger Motor Rubber Vibration Damper Gasket: CU-RG Englander Control Board Fuse (5-AMP): PU-CBFShippingFree shipping on items over $99! 99% of orders ship the same day with some exceptions noted in the description above. We ship to the continental United States only. We do not ship to Alaska, Hawaii, or Puerto Rico.Returns Need to return a product that’s in new condition? We’ll take it back, no questions asked! All products on our website are eligible for our 30-Day Hassle-Free Returns with no restocking fee, unless otherwise stated. All returned products must be in new condition, unused, and with their original packaging. All products are tested before refunds are issued. Products not in working order are not eligible for a refund. Stove & Grill Parts For Less does not supply return shipping labels for any products being returned. All return shipping costs are the responsibility of the purchaser, and will not be refunded. We do not charge a restocking fee for any item returned to our return shipping address within 30-days of purchase.Support We're here to help you every step of the way! Need help with your order? Contact us today for friendly and knowledgeable customer service!Warranty Issue with your order? Mistakes happen, but we’re here to help! If you've received a damaged, defective, incorrect, lost, or missing item(s) from your order, we will replace these item(s) after verification, or provide a refund if they have gone out of stock. Please submit all claims on our easy to use claims form. Stove & Grill Parts For Less was started over 20 years ago with a simple mission; Provide second-to-none replacement parts for a fraction of the competitions price. Over two decades later our friendly and knowledgeable team are still here doing just that! We take pride in satisfying our customers throughout the entire order process. With automatic tracking numbers, hassle free return policies, and knowledgeable sales members we cut no corners when it comes to our valued customers. We were once customers looking for stove parts just like you, and that is exactly what lead us to founding Stove & Grill Parts For Less! With thousands of parts available from every well known manufacturer in the pellet, grill, gas, and smoker industry we are sure to have what you are looking for. We also carry aftermarket versions that perform as well if not better than the manufacturer's part! And you won’t believe the savings!

Price: 149.99 USD

Location: North Falmouth, Massachusetts

End Time: 2024-12-04T12:27:06.000Z

Shipping Cost: N/A USD