Description: Not CARB Legal: Not for sale or street use in CA & CARB states.Part Number 30-4350 Superseded to 30-0352You are bidding on a Brand New Set of AEM Includes:30-4110 AEM Digital Wideband UEGO Gauge30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP Sensor30-4110 AEM Digital Wideband UEGO GaugeInterchangeable black and white faceplates included for customizing gauge appearance (digital gauges only)Bosch 4.9 LSU wideband sensor and weld-in bung included (PN 30-4110)No free air sensor calibration required - everInterchangeable black and silver bezels includedInterchangeable black and white faceplates included52mm (2-1/16âÂÂ) gauge housing0-5v analog output (10-20 AFR range only)30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP SensorOverview(NOTE: The original 30-4350 Tru Boost Controller Gauge is discontinued and has been replaced with the 30-0352 X-Series Tru-BoostX Controller Gauge, below)The Tru-BoostX Boost Controller Gauge delivers all of the features you loved about the original only now with AEMnet for data logging and a big, fat internal MAP sensor that can handle boost pressures up to 80 PSI of boost.The Tru-BoostX Boost Controller gauge delivers digital accuracy but with the simplicity of a manual boost controller. All programming is done using the faceplate buttons and no laptop is required. AEMâÂÂs specially designed Boost Control Solenoid and all necessary hardware is included.Program Two Boost Levels + Scramble Boost Setting â Program two boost modes for different levels of performance (up to 80PSIg internal MAP sensor), and program a time-based scramble boost setting that is controlled using a switched input. You can also turn off the controller and use the gauge as a display.Change Wastegate Open PressureâÂÂIdeal for reducing boost spikes and improving spool up.Display Boost Levels in PSIg (PSI), BAR or kPa (PAS) âÂÂSee your boost in the units you prefer, and scale the 24 outer LEDs to match your peak boost levels for the perfect sweeping motion.Set Alarms and Display Peak BoostâÂÂSet the 24 green outer LEDs to flash based on boost pressure so you are alerted to an overboost condition. A ground output is included for triggering an optional LED warning light. Select the âÂÂBâ button to see peak boost level and clear the value using the menu.Overboost Protection Built InâÂÂProtects your engine from an overboost condition by shutting the boost control solenoid off until it is reactivated by you through the buttons on the faceplate.Integrated Error ProtectionâÂÂAlerts you to a fault if the boost control solenoid is shorted or disconnected so you are never left guessing whether the Tru-BoostX is operational.Datalog using AEMnet CAN busâÂÂOutputting channels over AEMnet provides so much more than just boost pressure! Send 13 channels of data over a 2-wire connection, including boost pressure, peak boost, boost target, boost scramble duty, overboost status, wastegate crack pressure, boost control solenoid status and more.Features:A boost display gauge and boost controller in one!Easy to program â no laptop requiredBoost control solenoid and all necessary hardware includedOn-board 80PSIg MAP sensorâÂÂno upgrade kit needed for high boost vehiclesTwo boost level settings and scramble boost settingWastegate open pressure setting for controlling boost spikes and faster spoolDisplay boost levels in PSI, BAR or kPaOverboost protection and programmable alarms, ground output for optional LED warning lightPeak boost level recallX-Series design for the best visibility (87% larger center LED and 33% larger face design)X-Series dimensions make it easier to install (0.825â overall depth, 0.20â cup depth)AEMnet CAN bus enabled for data logging (13 channels of data over 2-wire connection)Standard 52mm (2-1/16âÂÂ) cup24 programmable green outer LEDsAuto dimming sensor for ideal brightness day or nightPositive locking connectors AEM 2 Gauges Combo Set - X Series Boost Control & Display + UEGO 4.9LSU WideBand AEM 2 Gauges Combo Set - X Series Boost Control & Display + UEGO 4.9LSU WideBand Not CARB Legal: Not for sale or street use in CA & CARB states.Part Number 30-4350 Superseded to 30-0352You are bidding on a Brand New Set of AEM Includes:30-4110 AEM Digital Wideband UEGO Gauge30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP Sensor30-4110 AEM Digital Wideband UEGO GaugeInterchangeable black and white faceplates included for customizing gauge appearance (digital gauges only)Bosch 4.9 LSU wideband sensor and weld-in bung included (PN 30-4110)No free air sensor calibration required - everInterchangeable black and silver bezels includedInterchangeable black and white faceplates included52mm (2-1/16”) gauge housing0-5v analog output (10-20 AFR range only)30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP SensorOverview(NOTE: The original 30-4350 Tru Boost Controller Gauge is discontinued and has been replaced with the 30-0352 X-Series Tru-BoostX Controller Gauge, below)The Tru-BoostX Boost Controller Gauge delivers all of the features you loved about the original only now with AEMnet for data logging and a big, fat internal MAP sensor that can handle boost pressures up to 80 PSI of boost.The Tru-BoostX Boost Controller gauge delivers digital accuracy but with the simplicity of a manual boost controller. All programming is done using the faceplate buttons and no laptop is required. AEM’s specially designed Boost Control Solenoid and all necessary hardware is included.Program Two Boost Levels + Scramble Boost Setting – Program two boost modes for different levels of performance (up to 80PSIg internal MAP sensor), and program a time-based scramble boost setting that is controlled using a switched input. You can also turn off the controller and use the gauge as a display.Change Wastegate Open Pressure—Ideal for reducing boost spikes and improving spool up.Display Boost Levels in PSIg (PSI), BAR or kPa (PAS) –See your boost in the units you prefer, and scale the 24 outer LEDs to match your peak boost levels for the perfect sweeping motion.Set Alarms and Display Peak Boost—Set the 24 green outer LEDs to flash based on boost pressure so you are alerted to an overboost condition. A ground output is included for triggering an optional LED warning light. Select the “B” button to see peak boost level and clear the value using the menu.Overboost Protection Built In—Protects your engine from an overboost condition by shutting the boost control solenoid off until it is reactivated by you through the buttons on the faceplate.Integrated Error Protection—Alerts you to a fault if the boost control solenoid is shorted or disconnected so you are never left guessing whether the Tru-BoostX is operational.Datalog using AEMnet CAN bus—Outputting channels over AEMnet provides so much more than just boost pressure! Send 13 channels of data over a 2-wire connection, including boost pressure, peak boost, boost target, boost scramble duty, overboost status, wastegate crack pressure, boost control solenoid status and more.Features:A boost display gauge and boost controller in one!Easy to program – no laptop requiredBoost control solenoid and all necessary hardware includedOn-board 80PSIg MAP sensor—no upgrade kit needed for high boost vehiclesTwo boost level settings and scramble boost settingWastegate open pressure setting for controlling boost spikes and faster spoolDisplay boost levels in PSI, BAR or kPaOverboost protection and programmable alarms, ground output for optional LED warning lightPeak boost level recallX-Series design for the best visibility (87% larger center LED and 33% larger face design)X-Series dimensions make it easier to install (0.825” overall depth, 0.20” cup depth)AEMnet CAN bus enabled for data logging (13 channels of data over 2-wire connection)Standard 52mm (2-1/16”) cup24 programmable green outer LEDsAuto dimming sensor for ideal brightness day or nightPositive locking connectors Not CARB Legal: Not for sale or street use in CA & CARB states. Part Number 30-4350 Superseded to 30-0352 You are bidding on a Brand New Set of AEM Includes: 30-4110 AEM Digital Wideband UEGO Gauge 30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP Sensor 30-4110 AEM Digital Wideband UEGO Gauge Interchangeable black and white faceplates included for customizing gauge appearance (digital gauges only) Bosch 4.9 LSU wideband sensor and weld-in bung included (PN 30-4110) No free air sensor calibration required - ever Interchangeable black and silver bezels included Interchangeable black and white faceplates included 52mm (2-1/16”) gauge housing 0-5v analog output (10-20 AFR range only) 30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP Sensor Overview (NOTE: The original 30-4350 Tru Boost Controller Gauge is discontinued and has been replaced with the 30-0352 X-Series Tru-BoostX Controller Gauge, below) The Tru-BoostX Boost Controller Gauge delivers all of the features you loved about the original only now with AEMnet for data logging and a big, fat internal MAP sensor that can handle boost pressures up to 80 PSI of boost. The Tru-BoostX Boost Controller gauge delivers digital accuracy but with the simplicity of a manual boost controller. All programming is done using the faceplate buttons and no laptop is required. AEM’s specially designed Boost Control Solenoid and all necessary hardware is included. Program Two Boost Levels + Scramble Boost Setting – Program two boost modes for different levels of performance (up to 80PSIg internal MAP sensor), and program a time-based scramble boost setting that is controlled using a switched input. You can also turn off the controller and use the gauge as a display. Change Wastegate Open Pressure—Ideal for reducing boost spikes and improving spool up. Display Boost Levels in PSIg (PSI), BAR or kPa (PAS) –See your boost in the units you prefer, and scale the 24 outer LEDs to match your peak boost levels for the perfect sweeping motion. Set Alarms and Display Peak Boost—Set the 24 green outer LEDs to flash based on boost pressure so you are alerted to an overboost condition. A ground output is included for triggering an optional LED warning light. Select the “B” button to see peak boost level and clear the value using the menu. Overboost Protection Built In—Protects your engine from an overboost condition by shutting the boost control solenoid off until it is reactivated by you through the buttons on the faceplate. Integrated Error Protection—Alerts you to a fault if the boost control solenoid is shorted or disconnected so you are never left guessing whether the Tru-BoostX is operational. Datalog using AEMnet CAN bus—Outputting channels over AEMnet provides so much more than just boost pressure! Send 13 channels of data over a 2-wire connection, including boost pressure, peak boost, boost target, boost scramble duty, overboost status, wastegate crack pressure, boost control solenoid status and more. Features: A boost display gauge and boost controller in one! Easy to program – no laptop required Boost control solenoid and all necessary hardware included On-board 80PSIg MAP sensor—no upgrade kit needed for high boost vehicles Two boost level settings and scramble boost setting Wastegate open pressure setting for controlling boost spikes and faster spool Display boost levels in PSI, BAR or kPa Overboost protection and programmable alarms, ground output for optional LED warning light Peak boost level recall X-Series design for the best visibility (87% larger center LED and 33% larger face design) X-Series dimensions make it easier to install (0.825” overall depth, 0.20” cup depth) AEMnet CAN bus enabled for data logging (13 channels of data over 2-wire connection) Standard 52mm (2-1/16”) cup 24 programmable green outer LEDs Auto dimming sensor for ideal brightness day or night Positive locking connectors AEM 2 Gauges Combo Set - X Series Boost Control & Display + UEGO 4.9LSU WideBand Item Description Not CARB Legal: Not for sale or street use in CA & CARB states.Part Number 30-4350 Superseded to 30-0352You are bidding on a Brand New Set of AEM Includes:30-4110 AEM Digital Wideband UEGO Gauge30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP Sensor30-4110 AEM Digital Wideband UEGO GaugeInterchangeable black and white faceplates included for customizing gauge appearance (digital gauges only)Bosch 4.9 LSU wideband sensor and weld-in bung included (PN 30-4110)No free air sensor calibration required - everInterchangeable black and silver bezels includedInterchangeable black and white faceplates included52mm (2-1/16”) gauge housing0-5v analog output (10-20 AFR range only)30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP SensorOverview(NOTE: The original 30-4350 Tru Boost Controller Gauge is discontinued and has been replaced with the 30-0352 X-Series Tru-BoostX Controller Gauge, below)The Tru-BoostX Boost Controller Gauge delivers all of the features you loved about the original only now with AEMnet for data logging and a big, fat internal MAP sensor that can handle boost pressures up to 80 PSI of boost.The Tru-BoostX Boost Controller gauge delivers digital accuracy but with the simplicity of a manual boost controller. All programming is done using the faceplate buttons and no laptop is required. AEM’s specially designed Boost Control Solenoid and all necessary hardware is included.Program Two Boost Levels + Scramble Boost Setting – Program two boost modes for different levels of performance (up to 80PSIg internal MAP sensor), and program a time-based scramble boost setting that is controlled using a switched input. You can also turn off the controller and use the gauge as a display.Change Wastegate Open Pressure—Ideal for reducing boost spikes and improving spool up.Display Boost Levels in PSIg (PSI), BAR or kPa (PAS) –See your boost in the units you prefer, and scale the 24 outer LEDs to match your peak boost levels for the perfect sweeping motion.Set Alarms and Display Peak Boost—Set the 24 green outer LEDs to flash based on boost pressure so you are alerted to an overboost condition. A ground output is included for triggering an optional LED warning light. Select the “B” button to see peak boost level and clear the value using the menu.Overboost Protection Built In—Protects your engine from an overboost condition by shutting the boost control solenoid off until it is reactivated by you through the buttons on the faceplate.Integrated Error Protection—Alerts you to a fault if the boost control solenoid is shorted or disconnected so you are never left guessing whether the Tru-BoostX is operational.Datalog using AEMnet CAN bus—Outputting channels over AEMnet provides so much more than just boost pressure! Send 13 channels of data over a 2-wire connection, including boost pressure, peak boost, boost target, boost scramble duty, overboost status, wastegate crack pressure, boost control solenoid status and more.Features:A boost display gauge and boost controller in one!Easy to program – no laptop requiredBoost control solenoid and all necessary hardware includedOn-board 80PSIg MAP sensor—no upgrade kit needed for high boost vehiclesTwo boost level settings and scramble boost settingWastegate open pressure setting for controlling boost spikes and faster spoolDisplay boost levels in PSI, BAR or kPaOverboost protection and programmable alarms, ground output for optional LED warning lightPeak boost level recallX-Series design for the best visibility (87% larger center LED and 33% larger face design)X-Series dimensions make it easier to install (0.825” overall depth, 0.20” cup depth)AEMnet CAN bus enabled for data logging (13 channels of data over 2-wire connection)Standard 52mm (2-1/16”) cup24 programmable green outer LEDsAuto dimming sensor for ideal brightness day or nightPositive locking connectors Not CARB Legal: Not for sale or street use in CA & CARB states. Part Number 30-4350 Superseded to 30-0352 You are bidding on a Brand New Set of AEM Includes: 30-4110 AEM Digital Wideband UEGO Gauge 30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP Sensor 30-4110 AEM Digital Wideband UEGO Gauge Interchangeable black and white faceplates included for customizing gauge appearance (digital gauges only) Bosch 4.9 LSU wideband sensor and weld-in bung included (PN 30-4110) No free air sensor calibration required - ever Interchangeable black and silver bezels included Interchangeable black and white faceplates included 52mm (2-1/16”) gauge housing 0-5v analog output (10-20 AFR range only) 30-0352 AEM X-Series Boost Control & Display w/ 80 PSI Internal MAP Sensor Overview (NOTE: The original 30-4350 Tru Boost Controller Gauge is discontinued and has been replaced with the 30-0352 X-Series Tru-BoostX Controller Gauge, below) The Tru-BoostX Boost Controller Gauge delivers all of the features you loved about the original only now with AEMnet for data logging and a big, fat internal MAP sensor that can handle boost pressures up to 80 PSI of boost. The Tru-BoostX Boost Controller gauge delivers digital accuracy but with the simplicity of a manual boost controller. All programming is done using the faceplate buttons and no laptop is required. AEM’s specially designed Boost Control Solenoid and all necessary hardware is included. Program Two Boost Levels + Scramble Boost Setting – Program two boost modes for different levels of performance (up to 80PSIg internal MAP sensor), and program a time-based scramble boost setting that is controlled using a switched input. You can also turn off the controller and use the gauge as a display. Change Wastegate Open Pressure—Ideal for reducing boost spikes and improving spool up. Display Boost Levels in PSIg (PSI), BAR or kPa (PAS) –See your boost in the units you prefer, and scale the 24 outer LEDs to match your peak boost levels for the perfect sweeping motion. Set Alarms and Display Peak Boost—Set the 24 green outer LEDs to flash based on boost pressure so you are alerted to an overboost condition. A ground output is included for triggering an optional LED warning light. Select the “B” button to see peak boost level and clear the value using the menu. Overboost Protection Built In—Protects your engine from an overboost condition by shutting the boost control solenoid off until it is reactivated by you through the buttons on the faceplate. Integrated Error Protection—Alerts you to a fault if the boost control solenoid is shorted or disconnected so you are never left guessing whether the Tru-BoostX is operational. Datalog using AEMnet CAN bus—Outputting channels over AEMnet provides so much more than just boost pressure! Send 13 channels of data over a 2-wire connection, including boost pressure, peak boost, boost target, boost scramble duty, overboost status, wastegate crack pressure, boost control solenoid status and more. Features: A boost display gauge and boost controller in one! Easy to program – no laptop required Boost control solenoid and all necessary hardware included On-board 80PSIg MAP sensor—no upgrade kit needed for high boost vehicles Two boost level settings and scramble boost setting Wastegate open pressure setting for controlling boost spikes and faster spool Display boost levels in PSI, BAR or kPa Overboost protection and programmable alarms, ground output for optional LED warning light Peak boost level recall X-Series design for the best visibility (87% larger center LED and 33% larger face design) X-Series dimensions make it easier to install (0.825” overall depth, 0.20” cup depth) AEMnet CAN bus enabled for data logging (13 channels of data over 2-wire connection) Standard 52mm (2-1/16”) cup 24 programmable green outer LEDs Auto dimming sensor for ideal brightness day or night Positive locking connectors Shipping We ship Monday-Friday and strive for orders to ship within 1-2 business days. We use UPS and FedEx for the majority of our orders but reserve the right to use alternative but comparable means to get you your product as quickly and efficiently as possible. All orders will require a physical address, please provide this upon ordering to expedite the shipping process. Even with our huge inventory, we may run out of an item. If this is the case you will receive an email with an expected availability date. Returns & Warranty We offer 30 Day Free Returns. Refunds for returns will be given once the item has been received and inspected. Items must be New, Unused, Not Installed, in the Original Packaging and able to be resold. Incomplete returns may not be eligible for this policy. Please message us to start a return. Warranty on product is replacement of part only for defects in materials and workmanship. No cash or compensation for labor will be given for defects in material and workmanship. Defective part must be returned in order for new part to be provided. OUR COMMITMENT We are committed to making sure that you leave this transaction satisfied. We value your feedback, and we strive to do everything we can to earn Five Stars and Positive Feedback on every order. If you are unhappy with your purchase for any reason, please CONTACT US prior to leaving feedback so that we can make things right for you. Contact Us We encourage our Buyers to communicate with us at any time. Feel free to contact us directly through eBay. All emails will be responded to within 24 hours. We look forward to hearing from you! Powered By 3Dsellers.com - Try for Free!
Price: 587.62 USD
Location: Memphis, Tennessee
End Time: 2025-01-10T11:09:45.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Return shipping will be paid by: Seller
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Return policy details:
Brand: AEM
Fitment Type: Performance/Custom
Manufacturer Warranty: 1 Year
Interchange Part Number: AEM A/F Gauge, AEM Wideband Controller Gauge, Peak boost level recall, 24 programmable green outer LEDs, Auto dimming sensor for ideal brightness day or ni, Positive locking connectors,, Two boost level settings & scramble boost setting, Display boost levels in PSI, BAR or kPa, Wastegate open pressure setting
Modified Item: No
Items Included: Bosch 4.9 LSU wideband sensor, Weld-in bung, Interchangeable black and white faceplates, Interchangeable black and silver bezels, Boost Control Solenoid, A ground output, all necessary hardware
Size: Standard 52mm (2-1/16”)
Old Part Number: 30-4110 + 30-4350
Gauge type: Digital Air/Fuel Ratio & Tru-BoostX
Superseded Part Number: 30-0352, 30-4100
Non-Domestic Product: No
Bundle Description: AEM 30-4110 & 30-0352
Manufacturer Part Number: 30-4110 + 30-0352
Custom Bundle: Yes
Part Number: 30-4350 Superseded to 30-0352