Description: The resin 1:1 mix ratio by volume, 64oz kit is volume 64oz mixed, is the total volume 64OZ kit : 32oz resin A +32oz hardener B (Total 64oz) Pakage included : 2X 64oz Kit (Bulk 1 Gallon total) Specifications: Mix Ratio...............1:1 by volume Work time ..............30-45 minutes Hardness....................D70-80 Mixed Viscosity..........2500-3500cps. Chemical Resistance.......excellent Moisture Resistance........excellent FDA Compliant / Food grade: Yes, in its inert fully cured state Heat resistance: up to 80℃ (please don't leave hot pans on it,a coaster needed) Approximate Coverage: 12 square ft per gallon at 1/8 inch thicknessDescription:The clear epoxy coating and casting system features a 1:1 mix ratio, offering a pourable solution that is scratch and water resistant. It provides an exceptional wet gloss finish with unmatched depth and clarity. Formulated for all coating and step casting applications, it is ideal for coffee tables, river tables, side tables, bar tops, countertops, and small void filling live-edge tables. Each time mixed, pour No more than 150ml total, (that is 75ml A + 75ml B, A must be ≥ B), with a thickness range of ≤1.2" to avoid bursting.Stay under 1.2" per pour.After the surface film cures begin your second pour.This ultra-clear epoxy resin system is perfect for professional applications, delivering superior performance. The resin 1:1 mix ratio by volume, 64oz kit is volume 64oz mixed, is the total volume 64OZ kit : 32oz resin A +32oz hardener B (Total 64oz) Pakage included : 2X 64oz Kit (Bulk 1 Gallon total) Specifications:Mix Ratio...............1:1 by volumeWork time ..............30-45 minutesHardness....................D70-80Mixed Viscosity..........2500-3500cps.Chemical Resistance.......excellentMoisture Resistance........excellentFDA Compliant / Food grade: Yes, in its inert fully cured stateHeat resistance: up to 80℃ (please don't leave hot pans on it,a coaster needed)Approximate Coverage: 12 square ft per gallon at 1/8 inch thickness Usage:1. The resin 1:1 mix ratio by volume, Stay under 1.2" per pour.2. Stirring must be uniform, especially the inner wall of the container, the bottom, etc, about 2-3 minutes. You can use glass rods, bamboo sticks, etc. After mixed,this product is better to let stand for 3-5 minutes.before used in order to break the bubbles which produced when it was mixing in time.3.the surface set time is roughly 1 hour at room temp(the full cure time is 8-12 hours in summer and 12-24 hours in winter) the hardness range is 70-80D after full cure.4. Please try a little bit before using the product a lot, so that would master the skills and avoid mistakes.5. When using crystal glue, be careful not to stick it on your hands or body. If this happens, wipe off the glue with a cloth or paper towel, then rinse with water soap or detergent. Note:Please Store Away from LightKeep Away from Childrens ReachUse Proper PpeEach Time the Resin Mixed with a Thickness Range of ≤1.2"to Avoid Bursting Question：Q:Why are there bubbles in the finished product?A:Stir too fast when adjusting the glue, and pour into the mold before the bubbles have completely subsided. Or after pouring the glue into the mold, the inner wall of the mold is not observed. If there are bubbles, please cut them off in time.Q:Why is the finished product soft?A:Inaccurate adjustment of the glue ratio will cause the finished product to not solidify, and the glue will not be thoroughly mixed evenly during stirring, and there will be wire drawing in the glue, and the mold will be demolded if it is not completely solidified.Q:What should I do if I get Epoxy?A:It can be washed directly with water, or wiped with a nail remover towel before washing. Q:Can it be put in the sun or in the refrigerator?A:Do not expose to the sun for a long time. Excessive exposure to ultraviolet rays will make the finished product fade and yellow. Putting glue in the refrigerator will greatly extend the fixed time.PaymentDelivery detailsReturn policyAbout usContact usPaymentWe accept Paypal,Google Pay,VISA,Master Card,American Express and Discover.Delivery detailsWe usually ship from US within 1-3 business days with tracking number.Return policy30 days returns. Seller pays for return shipping.About usWe are a trustworthy and professional card protection supplier.Contact usIf need any assistance about our product and service,contact us for free at any time via eBay messages.
Price: 42 USD
Location: Hebron, Kentucky
End Time: 2024-12-07T10:20:04.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Seller
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Brand: FUNEPOXY
Color: Clear
Handmade: Yes
Hardness: 80-85D
Model: Clear Epoxy Resin
