Quick Fuel 30-125-1R Racing 125 GPH Electric Fuel Pump With Regulator

Description: NEW Quick Fuel 30-125-1R Racing 125 GPH Electric Fuel Pump With Regulator Installation Instructions for 30-125-1R Electric Fuel Pump The QFT 125 GPH fuel pump is designed for drag race applications and is not well suited for continuous operation suchas over the road vehicles or industrial applications where there is little down time. If you use this pump on an applicationthat requires operation for extended periods of time it will shorten the life of this pump. Warning: this is a high pressure fuel pump (14 P.S.I.) and requires a fuel pressure regulator to bemounted between the fuel pump and carburetor! This electric fuel pump is designed to push fuel forward in the vehicle and is very ineffective at “pulling” fuel.Therefore, the fuel pump should be mounted in the rear of the vehicle, near the fuel tank and positioned so the inletside of the pump is gravity fed, that is, below the fuel tank itself. This fuel pump should not be mounted in the trunk or an enclosed area! NOTE: The two ports on this fuel pump are marked “IN” and “OUT”. Be certain to position the fuel pump correctly.1. The pump should also be mounted on a solid component of the frame, positioned vertically so the motor is on top. If you do not have an in-line filter now you should make provisions for the replacement of a fuel filter between the fuel tank andfuel pump. Two fuel filters would be highly recommended. 2. Check for possible interference with suspension and/or chassis components through the full range of travel.3. Check the lower portion of the pump in your chosen location - be certain it does not have a ground clearance problem or could possibly come in contact with debris that could be kicked up by the tire. 4. It is also recommended that all fuel lines be metal and you should avoid the use of rubber hose. Rubber hose in this location can be hazardous and the use of it is not advised. Route fuel lines away from any potential heat source, chaffiing,or road debris. Avoid tight bends and undersized fittings throughout the fuel line routing process. 5. Using the mounted bracket as a template, center punch and drill two holes to mount the pump. Note: the pump bracket slots are sized for 5/16” bolts. 6. Electrical connection is standard, the black wire is ground and the orange wire is positive. This pump will draw approximately 3 amps although in some applications it could draw up to 5 amps under severe load. To achieve optimumperformance it is crucial the pump receive battery voltage (13.8 volts approx.) at all times. You may consider using a relay toreduce the amperage load on the vehicle or chassis wiring. It is also strongly advised to use an oil pressure safety switch toshut the pump off if the engine is not running. 7. Always set the pressure regulator (see your pressure regulator instructions) before attempting to start the engine. Always use a fuel pressure gauge and check the gauge for accuracy often. 8. Fuel pump performance problems or failure is usually due to one of two problems: dirt and/or water. The clearances in a rotary vane fuel pump are extremely close and do not tolerate debris or corrosion - the presence of either element will severelyimpact the performance of your pump. Typically the fuel pressure will begin to fluctuate and the electrical amperage draw willincrease. If you follow these instructions and perform routine maintenance on the fuel filter you can minimize future problems.We thank you for purchasing a Quick Fuel Technology fuel pump. We are passionate about our products and your performance This product is covered by a 30 Day Limited Warranty as stated in Quick Fuel Technology’sSold as Each (1) Compatible with Today’s Complex Fuels CCS Kits are supplied with the highest quality components that meet or exceed original equipment specifications and all CCS kits are compatible with today’s complex fuel All returns must be pre-approved before returning. Absolutely No Refund on installed items or returned items in non-sellable condition. Buyer to pay returned shipping Cost. All Electrical items Carburetor Kits and Fuel Injection Kits will be shipped in sealed clear Package if the package is un-wrapped the item is nonreturnable. Carburetor Collectible Specialty Thanks You for Your Support! Please before leaving Feedback If you receive an order that does not meet your Expectations, please permit us the opportunity to fix the problem before leaving negative feedback or rating us. Keep in mind our prices are controlled by eBay rating process. We strive for perfection and welcome the opportunity to correct any issues with your order. Your satisfaction is our #1 importance. Shipping Time Most items will be shipped Same business day if ordered before 10:00 a.m. EST. A delay in payment equals a delay in shipping. Our Pro-Series Carburetors with customer specs will be shipped within five days. CCS Performance Carburetor is a complete service seller not an Empty Wagon Seller (drop shipper). Every item you see on our websites will be in stock and complete to ship within 24 hours of payment. In order to meet the price Competitive Ecommerce market, we purchase direct from the manufacturers in bulk quantities and package some items in house Contact us. Email is the quickest way to contact us. You will receive a response within 48 hours. Please limit your questions to the products we sell. If you have purchased one of our Performance Series Carburetors a Tech Support phone number will be provided in the technical information supplied with each carburetor purchase. Let CCS make your EBay experience a Great One!

Price: 175.95 USD

Location: Virginia Beach, Virginia

End Time: 2024-11-22T01:48:31.000Z

Shipping Cost: N/A USD