Red Dot Sight mount plate for GSG 922 CA fits DeltaPoint Leupold footprint RD

Description: in order to keep the price down we decided to make these plates out of carbon materials due to a nature of a 3D part this item is considered to be a disposable itemit may start disintegrating in about 500 rounds often more than that. sometimes it never happens Red Dot Mount Sight Plate for CA compliant GSG 922 gun with DeltaPoint Leupold footprint -------------------------------------------------------------------------------------------------------Please read to the end.This plates does not fit any GSG 922 gun.So Far Only GSG 922 CA compliant with a straight slide. We may produce plates that fit other guns in the future. Please make sure there is no large step-down behind the rear sight on your GSG gun.(like the pic below)see the pic below, this plate doesn't fit this type of dovetail !! What is a GSG gun?GSG guns are made by German Sports Guns, they make two models compliant with California Gun Roster, and this plate fits one of two guns. (.22 Cal) GSG922 and GSG1911I would not say ONLY, but I can not guarantee that it'll fit any other guns. It for sure doesn't fit the slide with a large step down after the rear sight.(there were several attempts to install on such)The current (available) plate is only good for GSG 922 with a straight slide and Trijicon footprint.recently we added two Footprints Red Dot sight for GSG 1911 with a small step down (see pix) It is made of a new material - Carbon Fiber PETG. So the price went up a little.The previous model is made of Carbon Fiber Nylon (slightly cheaper and has rough edges) Those two guns are on the CA Gun Roster.We can not guarantee that it would fit any other GSGHowever, a couple of purchases were on the GSG 922 guns without the California symbol.And it did fit. Ask questions if you are unsure of whether it is a fit for your gun.The plate was tested on GSG 922 CA versionMay fit other models of GSG guns with Novak cutouts dovetail without a step down behind the rear Iron Sight.Look at yours to make sure.May require some additional fitting with a needle file. Don't overdo it! An important note.There are concerns in the GSG CA Community that the .22 caliber has FTE problem, if you use red dot plates, so we've addressed that.Works well with High-Velocity rounds(we tested it with Fiocchi and CCI)Low-velocity rounds have cycling problems because of an increase in the slide weight.Therefore, the plate is made of an ultra light / strong polymer material. (not metal)Which is a lot easier to do the fitting with a needle file.We ran about a hundred rounds of Fiocchi and not a single jam Compatible Red Dot footprint patterns: (FITS SHIELD RMS/RMSC/SMS, JPOINT, REDFIELD ACCELERATOR, AND OPTIMA) Leupold,DELTAPOINT PROand Also: Holosun SCS 320-GR (SigP320)and Bushnell Electro-Optics (this is good for SigP320)RXS-100 Reflex Sight-------------------Remove the rear sight on your gun and replace it with our mount in order to mount your red dot. You can take our mount off and replace your rear sight at any time. Mounting screws included. Installation Instructions- Remove the rear sight*- Install the Sight Mount in the dovetail- Tighten set screw (if applicable)- Place the red dot sight on the Sight Mount(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight. This is up to you)- Apply blue Loctite to the provided mounting screws You can use a hammer with protective tape to put the plate instead of the iron sight but we do strongly recommend using a special device something like this (it will preserve the integrity of the slide) if you don't have it you can borrow it from a local gunsmith The product availability is based on the fact, that many .22 CA *roster guns*will never have an *optics-ready* option.We don't know when it will change.

Price: 39.64 USD

Location: Carlsbad, California

End Time: 2024-11-29T01:48:49.000Z

Shipping Cost: 4.95 USD