Talley Ring/Base 34mm High Fits Savage w/8-40 Screw Round Receiver w/Accutrigger

Description: Talley Manufacturing, Light Weight Ring/Base Combo, 34mm High, Fits Savage with 8-40 Screws... Round Receiver w/ Accutrigger Matte Finish Black 850719 Description: Made in America, these Savage Scope Mounts w/8-40 Screws made by Talley Manufacturing offer a unique and simplified one-piece scope ring and base solution for Savage rifles with round receivers, the AccuTrigger system and 8-40 screws (“the bigger screws”). This simplified mounting system eliminates the possibility of an “out of alignment” interface or “loose connection” between the ring and base of traditional two-piece designs. Ultimately this provides more strength and durability than rival steel rings and bases, but with a lighter overall weight. Fully CNC machined from lightweight aircraft-grade aluminum to the industries tightest tolerances, this rigid scope mounting platform requires no lapping and is ready to go out of the box. American Made, Lightweight Alloy Scope Mounts Fully CNC Machined High-Grade Lightweight Aircraft Aluminum Integrated Scope Ring and Base Design Lapping Not Required Designed to fit Savage round receiver rifles with the AccuTrigger system and 8-40 screws. Please verify screw size before ordering. Most Savage Ultra Lights and Timberlines are being produced with the 8-40 screws. Savage Scope Mounts w/8-40 Screws- Product Dimensions and Weights Ring Height Rear Height Front Height Available for Main Tubes Weight (per set) Extra-Low .300″ .300″ 1″ / 30MM 1.9oz / 2.2oz Extra-Low Extended .300″ .300″ 1″ / 30MM 2.0oz / 2.3oz Low .400″ .400″ 1″ / 30MM 2.0oz / 2.3oz Low Extended .400″ .400″ 1″ / 30MM 2.2oz / 2.4oz Medium .500″ .500″ 1″ / 30MM / 34MM 2.2oz / 2.4oz / 2.8oz Medium Extended .500″ .500″ 1″ / 30MM 2.3oz / 2.5oz High .600″ .600″ 1″ / 30MM / 34MM 2.3oz / 2.6oz / 2.9oz High Extended .600″ .600″ 1″ / 30MM 2.4oz / 2.7oz Extra-High .700″ .700″ 1″ 2.6oz Extra-High Extended .700″ .700″ 1″ 2.7oz 1 The height is measured from the top of the action/ receiver to the bottom of the scope tube at the respective mounting location 2 Hole spacing measured center to center. 3 Extended rings are typically used with long or magnum length actions when mounting a scope with a shorter main tube length. Front mount is offset by approximately 3/8 of an inch. Double Extended add approximately 3/8of an inch to each ring. Front hole spacing: .862 inches (21.89mm) Rear hole spacing: .862 inches (21.89mm) Sold in pairs. Includes mounting screws and wrench. (8-40 Screws / T-15) What height scope rings do I need for my Savage Scope Mounts w/8-40 Screws? Simplified method of determining required scope ring height Using some sort of shim (i.e. coins, washers, magnets) stack up the required number of shims to achieve desired scope height. Verify final height does not interfere with operation of bolt handle. Measure the final stack of shims. Torque Recommendations? Cap Screws on Rings: 17-20 in/lb on ring cap screws. Do not exceed scope manufacturer’s allowable torque specs on main tube. Always recommended to verify with scope manufacturer allowable torques to prevent marking or damage to scope tube. Always verify with the scope manufacturer the maximum allowable torque on main tube. Savage Scope Mounts w/8-40 Screws to Action: Torque can depend on the receiver. Please check with the rifle manufacturer (Savage) to verify allowable torque into receiver. Always make sure your torque wrench is calibrated, ...

Price: 59.95 USD

Location: Fort Worth, Texas

End Time: 2024-10-22T14:12:18.000Z

Shipping Cost: N/A USD