Description: Stock #: 717 See pictures for an example of what you will receive This item is pre-owned – it will work like new once programmed to your vehicle One (1) Aftermarket remote keyless entry fob alarm Transmitter control clicker keyfob controller replacement UNGO UNCO Loctronics ICD FCC ID: J5523518T1 ( Alternate Spelling: 15523518T1, J55235I8TI , J55235l8Tl ) Circuit board #: TX3B Frequency: 304 - 305 MHz PT2262 Circuit Board TX3B Tested- working 100% - red led light 3 button - ready too program battery installed LED color: Red 3 buttons Battery: GPA23 23GPA Normal 0 false false false EN-US X-NONE X-NONE Programming Instructions: Note: You can program up to 4 remotes to the system at one time. All existing remotes must be present and programmed at the same time. 1. Locate valet switch. 2. Insert key into ignition and turn to “on” position- (do not start the vehicle)- and then back “off”. 3. Repeat again- “ON”, “OFF”, “ON”- ending in the “ON” position. –The vehicle lights should flash at this point, indicating the vehicle has successfully entered programming mode. 4. Hold down Valet switch for 5 seconds. – Vehicle lights will flash again. 5. Within 15 seconds, hold down “lock” button on first remote- vehicle will confirm with a chirp or lights flashing when remote has been accepted. 6. Repeat step 5 with any remaining remotes. 7. To exit programming turn the key to “off” position. J5523518T1 Programming Instructions: METHOD #1: You will need two things 1.The remote control 2.Valet Switch (aka: programming switch) (you will see a single Push button switch typically red or blue button and in the kick panel area under front drivers dash) To program you have about 15 seconds¦ Can program up to 4 transmitters (program sequentially at the same time) 1.Get in vehicle 2.Key in Ignition 3.TURN ignition ON OFF ON OFF ON (leave on) 4.Lights in vehicle will flash leave key on 5.Grab valet switch 6.Push (hold down) button for 5 seconds 7.You will either hear a chirp or see a light flash let go 8.Grab transmitter (first to program) & hold down lock button until you either hear a chirp or see a light flash – let go 9.Grab 2nd remote & hold down lock button until you either hear a chirp or see a light flash let go 10.Grab 3rd remote & hold down lock button until you either hear a chirp or see a light flash let go 11.Grab 4th remote & hold down lock button until you either hear a chirp or see a light flash let go 12.Typically, about a 15 second window to do all of this in 13. To exit program, turn key off METHOD #2: Programming Instructions: This system uses Code Learning to learn up to 3 different transmitter codes. TO PROGRAM TRANSMITTERS TO ALARM: 1) Turn ignition switch ON then OFF 3 times quickly (on/off, on/off, on/off) until siren chirps once. 2) Leave ignition ON. 3) Push & Hold the Valet switch. The siren chirps 3 times. The system is now in programming mode. 4) Press BUTTON #1 on the transmitter- siren chirps once to confirm programming. Press BUTTON #1 on another transmitter within 5 seconds to program a second remote control. NOTE #1 If only one transmitter is being programmed, continue holding BUTTON #1 until Siren chirps a second time. This means the system has exited program mode. Hold the transmitter button until the siren chirps the 2nd time to prevent unauthorized code and noise from entering system. NOTE #2 Program Mode is exited automatically after 5 seconds of last code transmission or once 3 new codes have been programmed. System will disarm after programming. Disarm using any valid transmitter. 5) Turn Ignition to OFF. NOTE: When programming ALL remotes must be relearned! 100% Guarantee Remote Shipping / Return Policy Warranty/Returns: 1. We have a 30 day return policy. 2. All returns for replacements and refund need an RMA #. 3. Please contact us before returning items so we can give you the RMA # and the proper return address. 4. No refunds / replacements will be granted without an RMA# We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged. Please Note: Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement. Does this keyless remote entry come with a battery? Yes. It will have a working battery installed. Battery Condition: A. All remotes sold on Keyless4u include working batteries. B. Installed batteries are not tested for battery life- they are simply working. Some are new and some are used. Your vehicle will be installed with one of the following keyless entry systems: a. Standard Keyless Remote Packages: Installed at time of manufacture. b. Optional Keyless Remote Packages: Installed by a dealer. c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. d. No remote keyless entry system at all. The above information can change which remote you need for your installed remote keyless system.
Price: 39.55 USD
Location: Wellsboro, Pennsylvania
End Time: 2024-09-23T16:05:44.000Z
Shipping Cost: 6.96 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Non-Domestic Product: No
Other Part Number: Stock# 717
Warranty: 60 Day
Color: Black
Custom Bundle: No
Manufacturer Part Number: J5523518T1 J5523518TI keyfob control TX3B PT2262 transmitter
Modified Item: No
California Prop 65 Warning: N/A
Brand: Aftermarket Products
2-Way Paging: No
Type: Wireless
Unit Type: Unit
Part Brand: UNGO
Model: PT2262 Circuit Board TX3B FCC ID FCCID UNGO UNCO Loctronics ICD
Surface Finish: BLACK 3 BUTTONS RED LED
Features: keyless remote entry fob, PT2262 Circuit Board TX3B, Ready to Program - Batteries INSTALLED, TESTED - working 100%, comes with do it yourself programming instructions
Country/Region of Manufacture: Unknown
Unit Quantity: 1
